104.95104.951
OEM Toyota Factory Keyless Entry Remote HYQ12BAN HYQ12BBX 89742-42120 3 ButtonRemote Tested Before Shipping, Guaranteed To Work
All vehicles that use this remote are onboard programmable, meaning you can program the vehicle to accept new remotes yourself without any special tools or knowledge. Free phone tech support is available if needed. Remote For Toyota: This is a replacement for Toyota Part Numbers 89742-20200, 89742-0C020, 89742-42120 and FCC ID HYQ12BAN ...
ToyotaHYQ12BAN HYQ12BBX 3 Button Fob1

OEM Toyota Factory Keyless Entry Remote HYQ12BAN HYQ12BBX 89742-42120 3 Button

Remote Tested Before Shipping, Guaranteed To Work

$104.95

Select Your Vehicle
Specifications
Item Specifics
Product Type
Regular Remote
Remote Programming
Onboard
RF Transmission
1Way
Frequency
315 MHz
LED
None
Buttons
3
Description

All vehicles that use this remote are onboard programmable, meaning you can program the vehicle to accept new remotes yourself without any special tools or knowledge. Free phone tech support is available if needed.


Remote For Toyota:

This is a replacement for Toyota Part Numbers 89742-20200, 89742-0C020, 89742-42120 and FCC ID HYQ12BAN or HYQ12BBX with 3 buttons. Remote is tested on a keyless entry tester for radio signal strength, battery strength, and proper functioning before shipping to you.  This works on: 2004-2005 Toyota Celica, 2004-2005 Toyota Echo, 2007-2008 FJ Cruiser, 2001-2007 Toyota Highlander, 2001-2003 Toyota Prius, 2001-2003 Toyota RAV-4 (Factory installed system), 2004-2005 Toyota Rav-4, 2004-2005 Toyota Tundra, 2006 Toyota Tundra (Double Cab and Single Cab).


Programming Procedure:

  • For 2004-2005 Celica, 2004-2005 Echo, 2001 and 2003 Highlander, 2001-2003 Prius, 2002-2003 Rav-4, 2005 Tundra:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition.
d. Close the driver’s door.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.

7. Open driver’s door.


  • For 2004 Tundra:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other door locks don’t matter).

2. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close, then open the drivers door.

4. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).
b. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
c. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the LOCK and UNLOCK buttons, press the UNLOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
c. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.

7. Close driver door.


  • For 2002 and 2004-2005 Highlander, 2001 Rav-4:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.

7. Open driver’s door.


  • For 2004-2005 Rav-4:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.

7. Open driver’s door.


  • For 2006-2007 FJ Cruiser, 2006-2007 Highlander:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.

7.  Open driver’s door.


  • For 2006 Tundra Double Cab:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is OPEN (all other doors are closed).
c. Driver door is unlocked.

2. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close then open the driver’s door.

4. Perform these steps within 40 seconds:
a. Perform 5 lock/unlock cycles again with the switch on the driver’s door starting with lock.
b. Insert the key in the ignition cylinder.
c. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the lock and unlock buttons, press the UNLOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice (two lock and unlock cycles), this means your remote has not been accepted. Repeat steps 6a and 6b until the door locks cycle only once.
c. Repeat steps 6a and 6b for each remote including old ones.

7. Close the driver’s door.


  • For 2006 Tundra Single Cab:

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition.
d. Close the driver’s door.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Repeat steps A and B for each new remote.

7. Open driver’s door.


The following vehicles can use this remote when equipped with the factory keyless entry system:

Toyota Celica (2004-2005), Toyota Echo (2004-2005), Toyota FJ Cruiser (2007-2008), Toyota Highlander (2001-2007), Toyota Prius (2001-2003), Toyota RAV4 (2001-2003), Toyota RAV4 (2004-2005), Toyota Tundra (2004-2005), Toyota Tundra (2006).

 

Accessories
  • Free Tech Support
  • Battery Included
  • Guaranteed To Work
  • Tested Before Shipping
Compare with similar products
OEM HYQ12BAN HYQ12BBX 3 Button FobToyotaOEM HYQ12BAN HYQ12BBX 3 Button FobAdd to Cart
Reviews
(0)
Pricefrom $104.95
Product TypeRegular Remote
Remote ProgrammingOnboard
RF Transmission1Way
Frequency315 MHz
LEDNone
Buttons3
Return Policy

OVERVIEW

At RAK we make returns as easy as possible. Our mission is to provide you with the best products and the best service in the industry. We understand that sometimes, customers change their minds about products that they order or simply do not need them anymore. We also know that customers are cautious about Return Policies since they are often tricky and misleading. Our goal is to make the return or exchange process trustworthy and as simple as 1-2-3.

RETURN POLICY

If for any reason you are not completely satisfied with your purchase, you may return the item within 30 days of delivery of your order. The following rules apply:

Products must be in the same condition we sent it in.

Shipping Fees are non-refundable.

All returns must be made by signing in, going to MY ACCOUNT, clicking order history, finding the order, click Return this item.There are few non-returnable products & services that may be offered on our website. It will indicate clearly in the product description if a different return policy applies.

Order cancellations can only be requested prior to shipment.

RETURN PROCEDURE

To return a product, you must first request a Return Merchandise Authorization (RMA) that is located in the MY ACCOUNT section next to each order item that you want to return. Once you've selected the items to return and the reason, you will be given return instructions.

EXCHANGE PROCEDURE

There are 2 ways you can go about exchanging a product:

Option 1 (Slower) - Use the standard return procedure to request an RMA for the part you need exchanged. In your request please specify the exact item(s) you would like to exchange to. Upon receipt of your returned product we will process an exchange and ship the new part. If there is a difference in the price, you will be either refunded or charged the difference.

Option 2 (Faster) - Order the new part over the phone and request to include a prepaid label to send back the first purchase for refund.

DEFECTIVE, DAMAGED, OR INCORRECT PRODUCTS

We all know that accidents happen sometimes. If your product(s) will arrive defective, damaged, or simply incorrect, please contact our customer service department as soon as possible. Please do not attempt to use or install the part! We will send you a replacement part and provide you with a prepaid return label to return the defective part. Product(s) must be returned to us within 30 days. If the damage was caused by a shipping courier, we will schedule a damage pick up by the courier.

ORDER CANCELLATIONS

When you request a cancellation of an order or a part it may take up to 24 business hours to process your cancellation claim. This process may involve voiding orders in computer systems, removing items from backorder logs, having operations personnel pull items from production schedules and sometimes stopping orders at the shipping dock. Also note that sometimes products ship more quickly than expected, so we recommend that you do not purchase alternative products until receiving final confirmation of your cancellation.

REFUNDS & CREDITS

After we accept your return, you will be issued a refund via the same payment method as you had originally used to place the order. The refund amount will be composed of the original purchase price minus shipping charges. You will be sent an email confirming receipt of the return and your credit. Please allow an additional 5-7 days for the credit to appear on your account.

Battery Replacement

Remote Batteries

Bring your old key fob back to life.

Buy CR2016 Battery

To replace the battery:

  1. Using a coin or equivalent, open the transmitter case.
  2. Remove the discharged transmitter battery by ballpoint pen. Insert the tip of ballpoint pen at the guide groove and lift.
  3. Put in a new transmitter battery with positive (+) side up. Close the transmitter case securely.
  4. After replacing the battery, check that the transmitter operates properly.

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Customer Reviews
Share your thoughts with other customers
Login to leave a review
Questions & Answers
Be first to ask a question

Get in Touch
  • Chipkeys
    2302 Ave U #79
    Brooklyn, NY 11229
  • 386.586.3650
  • CONTACT US
Get the Latest

SIGN UP TO HEAR ABOUT OUR NEW PRODUCTS AND SALES.

TEASoftware