All vehicles that use this remote are onboard programmable, meaning you can program the vehicle to accept new remotes yourself without any special tools or knowledge. Free phone tech support is available if needed.
Remote For Toyota:
This is a replacement for Toyota Part Number 08191-00922 and FCC ID BAB237131-056. Remote is tested on a keyless entry tester for radio signal strength, battery strength, and proper functioning before shipping to you. Works on: 2000-2002 Toyota 4Runner, 2000-2001 Toyota Avalon, 2000-2001 Toyota Camry (w/ Dealer installed), 2000-2003 Toyota Celica (w/ Dealer installed), 2003 Toyota Corolla (w/ Dealer installed), 2000-2003 Toyota Echo (w/ Dealer installed), 2000-2004 Toyota MR2, 2001-2003 Toyota Rav-4 (w/ Dealer installed), 2001 Toyota Sienna (w/ Dealer installed), 2002-2004 Toyota Tacoma, 2004 Toyota Tundra (w/ Dealer installed). This remote transmits on 304MHz.
Programming Procedure:
- For 2000-2001 Camry, 2001-2003 Celica, 2000-2003 Echo, 2000-2004 MR2, 2001-2003 Rav-4, 2001 Sienna, 2003 Tundra:
1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).
2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.
4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition.
d. Close the driver’s door.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
7. Open driver’s door.
- For 2001-2002 4Runner, 2000-2001 Avalon:
1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other door locks don’t matter).
2. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close, then open the driver’s door.
4. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).
b. Insert Key in ignition.
c. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
d. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the LOCK and UNLOCK buttons, press the LOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
c. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
7. Close driver door.
1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other door locks don’t matter).
2. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close, then open the drivers door.
4. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).
b. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
c. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
d. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the LOCK and UNLOCK buttons, press the UNLOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
c. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
7. Close driver door.
- For 2000 4Runner, 2000 Celica:
1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).
2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.
4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.
7. Open driver’s door.
- For 03 Corolla, 02-04 Tacoma:
1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).
2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.
4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.
7. Open driver’s door.
The following vehicles can use this remote when equipped with the factory keyless entry system:
Toyota 4Runner (2000-2002), Toyota Avalon (2000-2001), Toyota Camry (2000-2001), Toyota Celica (2000-2003), Toyota Corolla (2003), Toyota Echo (2000-2003), Toyota MR2 Spyder (2000-2004), Toyota RAV4 (2001-2003), Toyota Sienna (2001), Toyota Tacoma (2002-2004), Toyota Tundra (2003), Toyota Tundra (2004).